Halston Global

• High pressure spray
• Good flexibility
• Durability

Additional Information:

• Pay Mode Terms: Complete Payment Against PI
• Delivery Time: Ready stock
• Packaging Details: 100 pcs in 1 smallest packing

• Easy to fit
• Compatible
• High material strength

We bring forth a pristine range of MS Hose Clamps that is widely accepted in the industry. These products are provided in assorted sizes and dimensions that suits the diverse needs of the patrons. Moreover, our worm drives are designed in tandem with international quality standards. These are specifically manufactured, which resist high workloads owing to its unmatched performance. We offer our products in standards sizes as well as in custom sizes as per the clients’ requirement.

Features:

• Durability

• High strength

• Stability

Specifications:

• BS 5315: 1991, IS 4762: 2002 and DIN: 3017

Material:

• The Material used in Manufacture of MS Hose Clamps shall be selected at the manufacturer's discretion provided that the finished clamps are capable of passing the tests specified

Manufacture Screw:

• Shall be held captive in the Clamp Housing

Band:

• Band shall have a thread form commencing at the free end extending for a length sufficient to enable the clamp to be tightened on to the smallest diameter of component within the working range for which it is designed

Housing:

• The housing shall not be readily removable from the band

Finish:

• Clamp shall be smooth and free from burrs and sharp edges

• Clamp Produced other than from corrosion resistant material (Stainless Steel) shall be protected from electroplating coating of zinc as per Fe Zn12 of IS: 1573/1970 & BS: 1706-Zn3

Tests:

• Free running Torque Test: for this purpose the torque required to move the screw in either direction shall not exceed 1.5Nm i.e. (13.3 ibf /In or 0.16 kgf I m)

• Torque Test: The Clamp shall be tightened to 75% of the Torque Load, as shown in table

• On release, Clamp shall reveal no sign of permanent distortion of the housing, nor efficient functioning of the clamp size

• The Clamp shall then be retightened until permanent distortion or failure occurs, at this point torque load shall be in excess of the value shown in table

Hydraulic Pressure Test:

• The fluid used for the test shall be water at room temperature

• Torque applied shall not be more than 75% of the value

• Pressure shall be applied gradually from an external source until leakage or other failure occurs, at which stage the pressure shall be not less than appropriate value specified

The material used in band and housing is low carbon steel as per specifications derived by I.S.I. The screw is manufactured from free cutting steel confirming to its standard grades.
The material used in the manufacturing of 'JOLLY' brand clamps are procured from well reputed manufacturers with quality assurance test certificates.

Additional Information:

• Delivery Time: Ready stock
• Packaging Details: Box

• Easy to fit
• Compatible
• High material strength

• Durability
• High strength
• Stability

• BS 5315: 1991, IS 4762: 2002 and DIN: 3017

• The Material used in Manufacture of WORM DRIVE HOSE CLAMPS shall be selected at the manufacturer's discretion provided that the finished clamps are capable of passing the tests specified

• Shall be held captive in the Clamp Housing

• Band shall have a thread form commencing at the free end extending for a length sufficient to enable the clamp to be tightened on to the smallest diameter of component within the working range for which it is designed

• The housing shall not be readily removable from the band

• Clamp shall be smooth and free from burrs and sharp edges
• Clamp Produced other than from corrosion resistant material (Stainless Steel) shall be protected from electroplating coating of zinc as per Fe Zn12 of IS: 1573/1970 & BS: 1706-Zn3

• Free running Torque Test: for this purpose the torque required to move the screw in either direction shall not exceed 1.5Nm i.e. (13.3 ibf /In or 0.16 kgf I m)
• Torque Test: The Clamp shall be tightened to 75% of the Torque Load, as shown in table
• On release, Clamp shall reveal no sign of permanent distortion of the housing, nor efficient functioning of the clamp size
• The Clamp shall then be retightened until permanent distortion or failure occurs, at this point torque load shall be in excess of the value shown in table

• The fluid used for the test shall be water at room temperature
• Torque applied shall not be more than 75% of the value
• Pressure shall be applied gradually from an external source until leakage or other failure occurs, at which stage the pressure shall be not less than appropriate value specified